RE 30277, edition: 2017-02, Bosch Rexroth AG
Electronic pressure switch
Features
▶ Suitable for measuring pressures in hydraulic systems
as well as for transforming the measured values into
electronic signal values
▶ Sensor thin film measuring cell
▶ Connection cable with 4-pole M12 connector on the
housing
▶ Accuracy class 1.0
▶ Male thread or internal thread G1/4''
▶ Components in contact with the media made of
stainless steel and FKM
▶ Compact design
▶ One switching output and one analog output or two
switching outputs
▶ IO link V1.1
▶ Component series 3X
▶ Maximum operating pressure 600 bar
RE 30277 
Edition: 2017-02
Replaces: 2016-06
Type HEDE 10
Contents
Features 1
Ordering code 2
Technical data 3 ... 5
Dimensions 5
Operating and display elements 6
Electrical connection 6 ... 7
Mating connectors 7
Accessories 8
Further information 8
Inhalt
Features 1
Ordering code 2
Technical data
(For application outside these values, please consult us!) 3
Technical data
(For application outside these values, please consult us!) 4
Technical data
(For application outside these values, please consult us!) 5
Dimensions
(dimensions in mm) 5
Operating and display elements 6
Electrical connection according to DIN EN 175301-803 6
Electrical connection according to DIN EN 175301-803 7
Mating connectors according to DIN EN 175301-803 7
Accessories 8
Further information 8
2/8 HEDE 10 | Pressure switch
Bosch Rexroth AG, RE 30277, edition: 2017-02
Ordering code
01 Hydro-electric pressure switch HEDE10
02 Component series 30 … 39 (30 … 39: unchanged installation and connection dimensions) 3X
03 Pressure rating maximum 100 bar 100
Pressure rating maximum 250 bar 250
Pressure rating maximum 400 bar 400
Pressure rating maximum 600 bar 600
Output
04 1 switching and 1 analog output 1
2 switching outputs 2
Hydraulic connection
05 Internal thread G1/4 Gi
Male thread G1/4 Ga
Electrical connection
06 Individual connection
Without mating connector; connector M12 DIN EN 61076-2-101 without cable with M12 connector, A-coded K35
1)
Seal material
07 FKM seals V
Without seal (with internal thread) 0
Observe compatibility of seals with hydraulic fluid used! (other seals on request)
08 Further details in the plain text
*
01 02 03 04 05 06 07
HEDE10 – 3X / / /– – – *
1)
Mating connectors, separate order, see accessories
Accessories
▶ Mating connectors for the electrical connection see
page 7.
▶ Mounting clamp and protective cap see page 8.
Pressure switch | HEDE 10 3/8
RE 30277, edition: 2017-02, Bosch Rexroth AG
Technical data
(For application outside these values, please consult us!)
hydraulic
Pressure rating (measurement range) bar 100 250 400 600
Admissible overload pressure bar 300 500 800 800
Bursting pressure bar 400 1000 1600 2500
Switching point bar 1.0 ... 100 2 ... 250 4 ... 400 6 ... 600
Switch-back point, rP bar 0.5 ... 99.5 1 ... 249 2 ... 398 3 ... 597
in steps of bar 0.5 1 2 3
Hydraulic fluid
1)
See table below
Hydraulic fluid temperature range
(at the working port of the pressure switch)
°C –25 … +80
Viscosity range mm
2
/s 10 … 800
Maximum admissible degree of contamination of the hydraulic fluid;
Cleanliness class according to ISO 4406 (c)
Class 20/18/15
1)
Material in contact with medium V4A (1.4542), FKM (with male thread)
Pressure port ▶ Internal thread "Gi" G1/4
▶ Male thread "Ga" G1/4
general
Weight kg 0.26
Installation position Any
Ambient temperature range °C –25 ... +80
Storage temperature range °C –40 ... +100
Sine test according to DIN EN 60068-2-6:1996-05 10...2000 Hz, max. 20 g, 10 double cycles
Transport shock according to DIN EN 60068-2-27:1995-03 Half-sine 50 g / 11 ms, 3 x in positive direction,
3 x negative direction (a total of 18 single shocks)
Noise test according to DIN EN 60068-2-64: 1995-08 20...2000 Hz, 10 g
RMS
, 24 h
Conformity ▶ CE DIN EN 60947-1: 2007 / A1: 2011 / A2: 2014
DIN EN 60947-5-1: 2004 / A1: 2009
DIN EN 61058-1: 2002 / A2: 2008
DIN EN 60529: 1991 / A2: 2013
▶ UL UL, 508 17th edition File No E223220 (up to 350 bar)
Protection class according to DIN EN 60529 IP 65 / IP 67 with mating connector mounted and fitted
Protection class according to EN 50178 III
Hydraulic fluid Classification Suitable sealing materials Standards Data sheet
Mineral oils HL, HLP, HLPD, HVLP, HVLPD NBR, FKM, low-temperature
seals
DIN 51524 90220
Bio-degradable ▶ Insoluble in water HETG NBR, FKM ISO15380 90221
HEES FKM
▶ Soluble in water HEPG FKM ISO15380
Flame-resistant ▶ Water-free HFDU, HFDR FKM ISO 12922 90222
▶ Containing water HFC (Fuchs Hydrotherm 46M,
Petrofer Ultra Safe 620)
NBR ISO 12922 90223
1)
The cleanliness classes specified for the components must be
adhered to in hydraulic systems. Effective filtration prevents
faults and at the same time increases the life cycle of the
components.
For the selection of the filters, see www.boschrexroth.com/filter.
4/8 HEDE 10 | Pressure switch
Bosch Rexroth AG, RE 30277, edition: 2017-02
Technical data
(For application outside these values, please consult us!)
electric
Electrical connection M12 plug-in connection, gold-plated contacts
Input variables
Supply voltage U
B
18 to 30 VDC
Current consumption I < 50 mA
Isolation resistance mΩ >100 (500 VDC)
Output parameters
Analog output ▶ Current carrying capacity U 0 ... 10 VDC (minimum load 2000 Ω)
▶ Voltage I 4 ... 20 mA (max. load (U
B
– 10) x 50 Ω)
▶ Rise time (10 to 90 %) t 3 ms
Switching output ▶ Output function Normally open contact / normally closed contact programmable
▶ Current carrying capacity I 150; 200 (...60 °C); 250 (...40 °C) mA
▶ Voltage drop
U < 2.5 V short-circuit protection clocked
▶ Overload-resistant Yes
▶ Switching frequency f ≤ 170 Hz
Accuracy / variations
Characteristic curve deviation:
(according to end point setting DIN16086)
< ±0.5 %
Temperature coefficient in
nominal temperature range
▶ largest TK of the zero point 0.2 % / 10 k
▶ largest TK of the range 0.2 % / 10 k
Hysteresis < ± 0.25 %
Switching point accuracy < ± 0.5 %
Repetition accuracy 0.1 %
Programming options Hysteresis / window; normally open contact / normally closed
contact; activation, deactivation delay; damping; indicator unit /
diagnosis output
Long-term drift under reference conditions (6 months) 0.05 %
EMC ▶ EN 61000-4-2 ESD kV 4/8
▶ EN 61000-4-3 HF radiated V/m 10
▶ EN 61000-4-4 Burst kV 2
▶ EN 61000-4-5 Surge kV 1
▶ EN 61000-4-6 HF conducted V 10
Reaction times
Readiness delay time s 0.3
Min. reaction time switching output ms < 3
Adjustable delay time dS, dr s 0...50
Damping switching output (dAP) s 0...4
Damping analog output (dAA) s 0...4
Rise time analog output ms < 3
Watchdog integrated Yes
Switching cycles min. 100 million / 50 million with pressure rating 600 bar
Important information on hydraulic fluids:
▶ For more information and data on the use of other hydraulic
fluids, please refer to the data sheets above or contact us!
▶ There may be limitations regarding the technical valve data
(temperature, pressure range, life cycle, maintenance intervals,
etc.)!
▶ The flash point of the hydraulic fluid used must be 40 K higher
than the maximum solenoid surface temperature.
▶ Flame-resistant – containing water:
– Maximum pressure differential per control edge 50 bar
– Pressure pre-loading at the tank port >20% of the pressure
differential, otherwise increased cavitation
– Life cycle as compared to operation with mineral oil HL, HLP
50 to 100%
▶ Bio-degradable and flame-resistant: When using hydraulic fluids
that are simultaneously zinc-solving, zinc may accumulate
(700mg zinc per pole tube).
Pressure switch | HEDE 10 5/8
RE 30277, edition: 2017-02, Bosch Rexroth AG
Dimensions
(dimensions in mm)
Tightening torque
M
A
= 25 ... 35 Nm
1)
1 Status LEDs
2 4-digit alphanumerical display
3 Programming button
4 Dimension for "Gi" version with internal thread G1/4"
5 Dimension for "Ga" version with male thread G1/4"
Ø 18,9
Ø 27
Ø 34
104,7
90,7
1
2
3
M12 x 1
65
28,5
M12 x 1
49,5
G1/4
30
G1/4
5
5
4
14,5
Notice:
Oscillation-free installation is recommended.
1)
Depending on lubrication, seal and pressurization
Technical data
(For application outside these values, please consult us!)
IO-Link device
Transmission type COM2 (38.4 kBaud)
IO-Link revision 1.1
SDCI standard IEC 61131-9
Profiles Smart Sensor: Process Data Variable;
Device Identification, Device Diagnosis
SIO mode Yes
Required master port class A
Process data analog 1
Process data binary 2
Min. process cycle time t ms 2.3
Display
▶ Indicator unit 3 x LED green (bar, psi, MPa)
▶ Switching status 2 x LED yellow
▶ Measured values 4-digit alphanumerical display / alternating display
(red and green)
6/8 HEDE 10 | Pressure switch
Bosch Rexroth AG, RE 30277, edition: 2017-02
"K35" two switching outputs
n-switching (NPN) p-switching (PNP)
OUT1: Switching output or IO-Link
OUT2: Switching output
Color marking according to DIN EN 60947-5-2
OUT1: Switching output or IO-Link
OUT2: Switching output
Color marking according to DIN EN 60947-5-2
"K35" one switching and one analog output:
OUT1: Switching output or IO-Link
OUT2: 4...20 mA / 0...10 V
Color marking according to DIN EN 60947-5-2
Electrical connection according to DIN EN 175301-803
Operating and display elements
12345678
12
9
10
11
1 ... 8: indicator LEDs
LED 1 Switching status OUT1 (is illuminated when output 1 is switched through)
LED 8 Switching status OUT2 (is illuminated when output 2 is switched through)
LED 2 ... 7
1)
System pressure in the specified unit of measurement
9: Enter key [●]
Selection of the parameters and confirmation of the parameter values
10 and 11: Arrows up [▲] and down [▼]
Setting of the parameter values (permanent by continuous pressure; step-wise by pressing individually)
12: Alphanumerical display, 4-digit
Display of the current system pressure
Display of the parameters and parameter values
1)
With variant 1 switching and 1 analog output, these LEDs don’t
have any function.
Pressure switch | HEDE 10 7/8
RE 30277, edition: 2017-02, Bosch Rexroth AG
Mating connectors according to DIN EN 175301-803
Technical data: Designation Material no.
15
42
M 12x1
Ø10,5
04 POL (with 2 m cable) R900773031
04 POL (with 3 m cable) R900064381
04 POL (with 5 m cable) R900779498
04 POL (with 10 m cable) R913005668
39
04 POL (with 2 m cable) R900779504
04 POL (with 5 m cable) R900779503
04 POL (with 10 m cable) R913011722
Connection:
4620
M12x1
04 POL (without cable)
1)
R900773042
1
2
3
4
BN
WH
BU
BK
2
1
4
3
20
M12x1
30
36
Ø18
Ø15
04 POL (without cable)
1)
R900779509
1)
Protection class IP68
For more details and other lengths refer to RE8006 or upon request
When establishing the electrical connection, the protective
earthing conductor (PE
) must be connected correctly.
Connector view at the device:
Electrical connection according to DIN EN 175301-803
Bosch Rexroth AG, RE 30277, edition: 2017-02
8/8 HEDE 10 | Pressure switch
Bosch Rexroth AG
Hydraulics
Zum Eisengießer 1
97816 Lohr am Main, Germany
Telephone +49 (0) 93 52 / 18-0
documentation@boschrexroth.de
www.boschrexroth.de
© This document, as well as the data, specifications and other information set
forth in it, are the exclusive property of Bosch Rexroth AG. It may not be
reproduced or given to third parties without its consent.
The data specified above only serve to describe the product. No statements
concerning a certain condition or suitability for a certain application can be
derived from our information. The information given does not release the user
from the obligation of own judgment and verification. It must be remembered
that our products are subject to a natural process of wear and aging.
Further information
Notice:
For general information on safety, installation or
commissioning, see operating instructions:
07600-B Hydraulic valves for industrial applications
30277-01-B HEDE10-3x with two switching outputs
30277-02-B HEDE10-3x with switching output and analog
output
30277-PA Parameter description IO-Link
Mounting clamp for HEDE 10
Designation Material no.
Mounting clamp R900786138
Protective cap for HEDE 10
Designation Material no.
Protective cap M12 R901453193
Accessories
Ø 37,4
Ø 16
Ø 3
40,7
70
58
12
6,5
29
52
Ø 34